I use a valve on waste water to prevent back flow, but not limit the output. Then I put a valve on fresh water to limit its input to the amount needed minus waste water output. It does take a little to get up to 100%, but I haven’t had any issues lately.
Not that I’m aware of, but I’m not as knowledgeable as someone else. I’m hoping some quick research or someone better can help. If I remember I can look later on this evening, but can’t at the moment.
Someone more knowledge than me can correct me, but I’m pretty sure you could buy a newer bigger drive to replace an older drive. You obviously wouldn’t get the full capacity as it would be limited by the other older slower drives. However, you would get a, theoretically, more reliable drive than a random one on eBay. Then as you replace older drives eventually you could have increased size.
Caveat is that it will put stress on the old drive to rebuild, however you’d get that with any drive you put in. General wisdom I saw says to replace all the drives. Although that can be expensive.
I’m any case make sure you have a backup before you do any of the changes.
A little off topic, but on first glance I thought that website was called fart caller.
On topic, I’ve never Heard of this service. I still haven’t setup anything like this. Might give it a try.
The lock itself is fine. I can do pretty much everything with the zwave once paired. Locking and unlocking are pretty quick and easy. You can setup a few different numbers too (haven’t played with it too much once setup). It has a sensor to detect if the door is open, but it’s pretty slow. Sometimes I can open and close the door before it knows it’s open. More of a door left open sensor.
Our door lock it well aligned, but it’s yours is off I could see it being an issue, but that’s any motorized lock.
Battery life seems pretty good considering we use the lock multiple times a day. Just 4 AA batteries I Believe. It also beeps at you when you lock/unlock before it dies so you have a fair warning.
I have one. You still need the app to setup the lock, which is unfortunate. Once it was setup I just deleted the app.
I’ve used freetaxusa the last couple of years. If the IRS one isn’t available, then I’d recommend them.
It looks like it uses chrome for certain data, and I’m not a fan of that. Any idea if I can change that to use Firefox?
Not op, but some people seek the community that religion provides.
Hopefully someone smarter than me can help. You can always do what I do, and just blow up the install and start fresh. 😂
Darn.
I suppose you could also try using the lsof command to see if it shows anything different?
Some examples: https://www.cyberciti.biz/faq/unix-linux-check-if-port-is-in-use-command/
This may sound silly, but have you tried restarting? I feel like that worked for me when I had a similar issue in the past. Something was holding onto the port, but it wasn’t showing up anywhere. Restart got it to let go and it worked afterwards.
Lots of good suggestions. I’ve also used memos, but wasn’t a huge fan of how the notes were organized. Solid app and definitely worth a look.
https://github.com/usememos/memos
Edit: I’m holding out hope for when notesnook goes self-hosted.
Edit 2: after looking at my older instance I see they save the notes in a database and is not relevant to your question.
I agree about the controls. I played on PC many times beforehand. They did a decent job of adapting it to the steam deck.
Oof, purchased by an analytics company probably means they only want it for your/my information.
I’m trying one of the Dev releases that was linked below. So far it’s pretty stable. Not sure your tolerance for any issues that may arise.
Oh sweet! Thanks for the heads up! I was hoping to find a version 14 without having to figure out how to build it myself.
I took a peek into their telegram feed and it seems they’re working on version 14.
I’m sure you’ve done this, but you’ll want to make sure you’re using all of the water being input based on calculations.
For instance, if you’re making 100 m3/min and you need 400 m3/min for 100%. Then you’ll need to limit fresh intake to 300 m3/min. However, if your refineries aren’t running at 100% and maybe only using 300 m3/min then your waste won’t be used to full capacity.
To counter this I tend to starve the system of water by limiting fresh and then bumping it up until max is reached.
It’s a bit finicky, but seems to work for me.