He actually patched it already. WOW!!! So happy to have offline transcoded files back after leaving Plex!

The app works well enough but was unable to watch anything I downloaded offline on iOS. Has anyone experienced this and found a fix? I downloaded from the App Store, not Test Flight.

Thank you. This is great info. I will give this a shot when I can.

Thank you so much for continuing to try and help. It’s greatly appreciated. I am very new to Linux so while I can do some basics, this is very helpful. I installed pyUSB but still get an error when running the script. I have the script placed in my home folder. Should it be elsewhere? The error I get is “No module named ‘usb’. I did adjust the script to have my controller’s proper identification so feels like I’m missing a small piece of the puzzle!

Thank you for the continued effort to help! If I boot into windows and enable the “MB RPM Sync”, the fans are recognized by the BIOS and ramp up and down as needed. This setting does not persist after a shutdown tho. The only way I’ve found to consistently have the fans work as intended after a shutdown is to unplug the USB cable from the Lian Li controller, which kills RGB. I have the PWM connector from the controller going straight into one of the connectors on my mobo. I can tell that after a shutdown, the fans just rotate on their lowest setting, until I open L-Connect 3 again on windows or disconnect the usb port. I’m attempting to implement this: https://github.com/kryzaach/Lian-Li-Unifan-Sync but think I have it placed in the wrong location, as it errors out immediately.

An update: I fiddled with connecting the L-Connect controller to splitters, and a PWM and RGB hub I have and the results are the same: the Lian Li fans are not recognized by the BIOS unless I unplug the USB connection on the Lian Li controller, which kills RGB. When I used the splitter, it actually made my other fans invisible to the BIOS too. Looking closer, I noticed the PWM connector from the Lian Li controller only has 2 pins so I’m assuming it just won’t work without the L-Connect 3 software. Bummer

Thank you so much for the advice but the issue with the Lian Li Uni Fan v2 is that the fan connectors are proprietary and only fit into the controller. The only thing I could split is from the controller and I don’t think that would really change my current situation.

So you were right about one of my SATA connectors on my Lian Li controller being disconnected. I connected that but BIOS still doesn’t see the fans. Then I disconnected the USB connector from the Lian Li controller and my fans were recognized but no LED. I’m going to look into the other suggestion in this post. Thank you for taking the time to try and help!

If I shut down, it sees no fans on that header. If I run L-Connect 3, it shows a single fan’s speed, which is ultimately the controller driving the three fans

I think I did but I will check and get back to you! Thank you thank you!

Thank you for the advice! I tried to run the software in Bottles but while I could run the installer, launching the program threw an error 🤷‍♂️

Thank you so much for the reply! I have an MSI B550 Tomahawk, so a fairly new board. I can definitely relate to the OpenRGB issues as well. I appreciate the offer for your config but I have the lights as stable as they’ll get I think. I just tested again to be sure and when I shut down the system and go to the BIOS, fan 5 isn’t recognized. Right when I log into windows and enable MB Sync in L-Connect 3, the BIOS sees the fans again. I have 2 fans under my GPU and one as exhaust so I’ve noticed higher temps when in Linux. Thank you again for the input. I’ll need to dig around a bit more I suppose.

I recently started playing having only played an hour or two before and am having a blast. I’ve mostly sailed with a group of 3, which seems to deter people from attacking you. I say go for it!

This. I used a P1000 for transcoding and eventually switched to a 12th gen Intel chip with integrated UHD 770 graphics. It completely blew me away. Insanely low power draw and barely breaks a sweat transcoding multiple streams. Consider this route over a GPU if you can.

Really cool list. Thank you for sharing!

This guy is a great resource for Home Assistant and other smart home tech. I would start here https://youtu.be/ooFvyudbxNE?si=WzYS1IIyVS5TkmZ9

I absolutely love Zooz. Their customer service is fantastic and products just work, if you can provide proper Z-Wave coverage. If you prefer WiFi, I have several Shelly products behind traditional switches that have been rock solid.

Absolutely one of the most beautiful games I’ve played

Do you have Nginx on the same bridge as Overseerr? If you have multiple docker networks, they need to be on the same so they can discover one another. That bridge also needs internet access so you can generate the cert. Hope this helps

All hail the master https://youtu.be/znSu_FuKFW0?si=3zbwqKA6OpIMPc35